Exactly How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Exactly How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
This great article following next on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is immensely engaging. Don't bypass it.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old tub with a new one is additionally a moderately difficult job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you mount a new tub in your shower room if you have actually already purchased a new bathtub and also do not need to alter the plan of your previous water pipes.
Your tools as well as product list need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be attached to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub up until the spirit level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the proper supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water and also check all joints and new pipework for leakages as well as tighten them if necessary. Fill the tub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been used a minimum of once as this will settle it right into its last placement.
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bath and also the tiling, causing problems with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that article about Installing A Bathtub when doing research the web. If you enjoyed reading our blog posting kindly do not forget to share it. Thanks so much for taking the time to read it.
Click Here To Read More
Report this page